Vehicle conservation and extra what

motorcar amounted warranty, the second security, three security. vehicle upkeep checks a project as a replacement fuel, fuel percolate, oil filter, climate filter. Second, check the coolant liquid conveyance situation compliance. Third, check the brake and clutch surface location. Fourth, check the power steering oil tank surface is loyal with the provisions of the pipe inspection system interface namely a permeability phenomenon. Fifth, check the power cell surface and glass surface cleaning proxy tank. Sixth, check the generator, ventilation conditioning, water pump and booster pump strap traction and aging 7 or check the vehicle front and rear lights are complete (including: headlamps, depending above the width of lights, corner signals, brake lights, reversing lights and mist lamps.) Pat, check tire pressure and wear, tire screw anchoring torque necessitated, added to the vehicle tire pressure among the specified value, along apt swivel the tires wear. September, check whether the target vehicle emissions. Vehicle conservation inspection II Item 1. Engine operation through the three Qing filter, it ought be cozy apt begin, flat action,GHD Green Butterfly 2011, the exhaust is customary (refer to exhaust criteria), water temperature, oil pressure to meet the requirements, speed smooth, no abnormal sound, the belt Zhang moderately tight, not four-drain (water, oil, electricity, gas) phenomenon. 2. The instruction of free voyage and to meet the requirements ahead the beam, turning light, amenable, authentic, no shaking approximately the front wheel wag and discrepancy. 3. Clutch free travel to meet the requirements, effortless, completely insulated, with settled, reliable, no abnormal sound,GHD Purple Gift Set, leak-free hydraulic system. 4. Transmission, pedal axle, prevalent joints (or axle) transmission devices,GHD MK4 Gold Straighteners, good lubrication, reliable articulation, no abnormal sound and overheating, do no jump stop, shift flexible and not leaking. 5. Brake and brake drive free travel intermittently to meet the requirements, traffic, parking brake, agreeable braking, no brake drag deviation lag phenomenon and the phenomenon of inertia proportional valve is working, not leaking. 6. Tire pressure is natural (below another models of alter lofty and low criteria.) 7. Cantilever, damping constant, reliable, functional, wheel bearing temperature is not high fever later traveling. 8. Generator, starter, lights, gauges, lights, buttons, switches subsidiary entirely equipped, complete, and can go properly. 9. The entire point of filling the lubrication oil vehicle. 10. The whole car bathe clean. Three vehicle maintenance inspection program to convergence the disintegration of three cleaning and maintenance, inspection, adapted to megalopolis. Engine maintenance operations: (1) the disintegration of the engine, cleaning, inspection of all parts: cylinder block, cylinder pate should be clean and free of coke, oil, scale; oil duct cleaning smooth. (2) 50MM width of every cylinder pate surface roughness shall not exceed the 0.05MM. (3) shall not be less than the cylinder head valve seat airplane 0.5MM (whichever is the maximum point). (4) Cylinder pierce narrow, round loss shall be not Yuxian. (5) valve grinding: adjoin surface should be smooth, sealed, should not drip. (6), for the absence to replace the piston rings. (7) Check the crankshaft cardinal bearings and interlocking wand bearing clearance, the breach is too massive, tin be modified; (8) If the journal bearing is damaged or worn, replace and re-grinding mill journal bearings and light. (9) removal of coke; available scraper blade (or bamboo), metal brush to remove,GHD IV Styling Set, tin likewise be secondhand coke scavenger removal. (10) the replacement of cylinder head gasket. (11) measuring cylinder pressure: Check the engine speed. Chassis maintenance operations: (1) steering; to flexible, curtate, straight rod bend, no cracks, screw thread and keyway intact, flexible circulation, not Songkuang, locking appliance complete lock. (2) dismantling the steering: the decomposition of inspection, cleaning and replacement of damaged parts. After the installation should be rotating flexible mutual, wire wiring,GHD Red Straighteners, and the need to load test. (3) dismantling the hand,GHD Leopard Grain, foot brake, along to 2 maintenance requirements implementation. (4) Check all fittings, threaded pipe tee should be in nice condition, with near, not drip. Check the brake hose, not the friction with the bordering parts of the collision: the pipe shall not harm, leakage, drum kits, or stained with oil from the ground.