F1 problem

1 F1 key at boot, this is because your BIOS settings properly, but also the natural guidance system, is a non-fatal failure,GHD IV Dark Straighteners, along to F1 is asking you whether to continue.

you do not have floppy drives, but CMOS is set to open the floppy drive alternative.
is: begin at Del key to enter BIOS setup, select the 1st a setting not then press the Settings can.
3 boot absence to press the F1 key to enter,GHD, chiefly because the BIOS setting does not mate the real data deserving to hardware can be divided into the emulating situations:
1, virtually no floppy drive or floppy drive is broken, and BIOS settings are actually floppy drive,GHD Green Butterfly 2011, which led to the according to F1 to continue.
2, originally interlocked to two hard drives set to double in the BIOS, hard drive, then remove 1 of the period but forgot to alteration the BIOS settings behind, there will be the problem.
3, the battery does not power the motherboard tin likewise reason file detriment to occur in this failure.
4, restart the system, enter the BIOS setup, found is set to 1.44M floppy drive, but in fact there is no floppy drive chassis will be afterward this is set to NONE,GHD Hair Straightener, troubleshooting.
had a lot of human asked this question, I have come across the retinue will make a few concluding such problems, we want to help.
1, Hareware Monitor found one peccadillo, enter POWER MANAGEMENT SETUP because details, Press F1 to continue, DEL to enter SETUP

Chinese: monitoring errors are found, enter POWER MANAGEMENT SETUP View detailed message,GHD Straighteners, reception F1 key to continue the boot process, reception the DEL key to enter COMS setting.

Explanation: Some motherboards with hardware monitoring feature, you can set the motherboard and CPU temperature monitoring, voltage regulators, voltage Output Level fan speed monitoring and surveillance of all, while

The monitoring function is found to have abnormal boot, then there will be this corridor upon, then you can prefer to enter COMS set the POWER MANAGEMENT SETUP, at the right ** Fan Monitor **,** Thermal Monitor ** and * * Voltage Monitor ** see at what part of the publish of an exception, then add to address.

2, pri slavery drive-ATAPI LNCOMPatible press F1 to Resume
may be your drive is imperfect or not joined, the best port in the CMOS ambition set the IDE automatically.

3,GHD Red Straighteners, Press F1 to continue, DEL to enter SETUP
boot and press DEL to enter BIOS, select the floppy drive in the selection, press F10 NONE save on it

4, CMOS checksum error-Defaults loaded
Press F1 to contnue? DEL to enter SETUP
08/09/2000-i810-ITE8712-6A69ME1CC-00
cmos battery is dead.
5, Warning! CPU has been changed! Please Enter CPU speed CMOS install and Remember to retention Before Exit!
This shows BIOS settings are washed away, and want to reset the BIOS (also phoned CMOS settings). Power press Your CPU frequency? To be elected in the BIOS, FSB, multiplier because it is locked. FSB is always 66,100 or 133, relying above CPU prototype, from cheap to high settings. If the BIOS settings AWARD by family on co-optation Frequency / Voltage Control (frequency / voltage control), use the list to the frequency and voltage to a special setting. Including Various motherboard BIOS settings are alter, you can refer your motherboard handbook to accommodate.
6, cpu has been changed please re-enter cpu settings in the cmos setup and memorize to save before discontinue!
some have a FSB jumper on the motherboard, the default is 100MHZ, and some motherboards do not advocate auto-FM . You equitable put into the BIOS, set your CPU FSB FSB can be a criterion, frequency is automatically set to the general terms, it is best not to overclock.